Connect-Tek Transa PRO 17 Manuel d'instructions télécharger pdf (Page 8)

1–4 Keys and Displays

The unit is programmed by using the three keys on the front panel. The available key functions are listed in the following table.

°F

°C

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 91 92

Instruction Manual 1
TEC-9300 1
Self-Tune Fuzzy / PID Process 1
Temperature Controller 1
Chapter 1 Overview 5
Related Products 6
1–2 Ordering Code 6
Figure 1. Access Hole 7
Overview 7
Table 1.1 DIP Switch 7
Configuration 7
1–4 Keys and Displays 8
1–6 System Modes 11
1–7 Parameter Description 12
Chapter 2 Installation 19
2–6 Thermocouple Input Wiring 20
2–4 Power Wiring 20
2–7 RTD Input Wiring 21
2–8 Linear DC Input Wiring 21
2–10 Event Input wiring 23
2–11 Output 1 Wiring 24
2–12 Output 2 Wiring 25
Figure 2.19 RS-232 Wiring 28
3–1 Input 1 29
3–2 OUT1 and OUT2 Types 30
3–3 Configuring User Menu 30
3–4 Heat Only Control 30
3–5 Cool Only Control 31
3–6 Heat-Cool Control 32
3–7 Dwell Timer 33
3–8 Process Alarms 34
3–9 Deviation Alarm 35
3–10 Deviation Band Alarm 36
3–11 Heater Break Alarm 37
3–12 Loop Break Alarm 37
3–13 Sensor Break Alarm 38
3–14 SP1 Range 38
3–15 PV1 Shift 38
3–16 Failure Transfer 39
3–17 Bumpless Transfer 40
3–18 Self tuning 40
Self-tune Menu 40
3–19 Auto tuning 41
3–20 Manual Tuning 42
3–21 Signal Conditioner 43
DC Power Supply 43
3–22 Manual Control 43
3–23 Display Mode 44
3–25 Reload Default Values 44
4–1 Event Input 45
4–2 Second Set Point 45
4–3 Second PID Set 46
4–4 Ramp and Dwell 46
4–5 Remote Set Point 47
4–6 Differential Control 47
4–7 Output Power Limits 48
4–8 Data Communication 48
4–9 Analog Retransmission 49
4–10 Digital Filter 49
4–11 Sleep Mode 49
4–12 Pump Control 50
4–13 Remote Lockout 50
Chapter 5 Applications 51
5–3 Heat Only Control 52
5–5 Heat-Cool Control 53
5–4 Cool Only Control 53
5–6 Ramp and Dwell 54
5–7 Remote Set 55
5–8 Differential Control 55
5–9 Dual Set Point/PID 56
5–10 RS-485 57
5–11 RS-232 58
5–12 Retransmit 58
Chapter 6 Calibration 59
Troubleshooting procedures: 61
Chapter 8 Specifications 65
PID: Fuzzy logic modified 66
9-1 Functions Supported 67
9-2 Exception Responses 68
9-3 Parameter Table 69
P= 100.0 80
9-3 Communication Examples 80
A–1 Menu Existence Conditions 81
A–2 Factory Menu Description 84
A–3 Glossary 85
A–4 Memo 89
A–5 Warranty 91
TEMPCO’s Visionary Solutions 92

Commentaires sur ces manuels

Pas de commentaire

Connect-Tek Transa PRO 17 Manuel d'instructions Page 8

Commentaires sur ces manuels