Connect-Tek USB-16 Manuel d'utilisateur

MyWirelessTVModel #: MWTV200T, MWTV200R,MWTV200KIT User ManualVer 1.0Solutions for the Digital Life™

MyWirelessTV Receivere MyWirelessTV Receiver features three ports (Power, HDMI Out, USB), two buttons (Sync, Reset), and three LEDs (Wireless, Sync,

Power LED e Power LED, located on the front of the Receiver, is used to display the state of the Receiver’s power. If unlit, the unit is o. If lit,

Connecting MyWirelessTVConnecting MyWirelessTV consists of two parts: connecting the Transmitter to a source of high-denition video, and connecting t

7. Plug the other end of this HDMI cable to an HDMI port on the source device. is cable should now connect the Transmitter to the source device.8. Tu

Setting Up IR ControlMyWirelessTV comes with an IR Blaster and IR Receiver, which work together to allow you to control the source device from the loc

3. Place the at end of the IR Blaster cable in front of the remote sensor of the source device.You should now be able to use the remote control of th

ReceiverConnecting to a Computer as a Source DeviceIf you want to use a computer with an HDMI out port with MyWirelessTV, connect the computer as you

Using USB Backchannel1. Aer connecting the computer to the Transmitter, and an HD monitor to the Receiver, get the mini USB connector from the kit an

Using the MyWirelessTV Graphical User Interfaceis chapter describes using the MyWirelessTV graphical user interface, which allows you to congure var

ButtonsTo navigate the GUI screens, you must use several of the buttons on the remote control. Following is a list of the buttons needed to navigate t

Table of ContentsIntroduction 3Minimum System Requirements 3Features 4Product Contents 5Getting To Know MyWirelessTV 6Connecting MyWirelessTV 11Connec

OKPressing this button conrms the selection made within theGUI.BackPressing this button returns you to the previous screen in the GUI (cancels the la

Graphical User InterfaceTo access MyWirelessTV’s graphical user interface, press the Menu button the remote control. e Main Menu appears:MyWirelessTV

Select SourceSelecting Select Source from the Main Menu screen (by navigating to the appropriate icon and the pressing OK on the remote control) gener

CongureSelecting Congure from the Main Menu screen (by navigating to the appropriate icon and the pressing OK on the remote control) generates the C

Label TransmitterSelecting Label Transmitter generates a list of names in the right-hand pane with which you can label the currently streaming source

General SettingsSelecting General Settings from the Main Menu screen (by navigating to the appropriate icon and the pressing OK on the remote control)

Latency ModeSelecting Latency Mode in the General Settings screen causes the Receiver to list the latency mode options (eater Mode and Game Mode) in

Advanced SettingsSelecting Advanced Settings from the Main Menu screen (by navigating to the appropriate icon and then pressing OK on the remote contr

Reset to FactorySelecting Reset to Factory in the Advanced Settings screen generates a window on the screen, asking the following: Are you sure you wa

4. Watch the Power and Sync LEDs of the device ash for 2-3 minutes. Do not power down the device or remove the USB thumb drive while the LEDs are as

Troubleshooting 29Frequently Asked Questions 29Specications 32General 32LED Indicators 33GPL License 33MyWirelessTV User Manual2

Troubleshootingis chapter will describe some problems you may encounter using MyWirelessTV, and the possible solutions to those problems. Also includ

Why can’t I change my channel or volume with the MyWirelessTV remote control?e remote control is intended only for switching inputs, pairing congura

I have my MyWirelessTV Receiver and Transmitter in the same room. Why does my source device accept the command from the remote control twice?To preven

Specicationsis chapter lists the specications of the MyWirelessTV devices.GeneralVideo SpecicationsMultisource: Multiple Transmitters‡ to 1 Receiv

USB: 1 USB Type A (Receiver); 1 USB Mini (Transmitter)Power: 5V 3AWeight: 0.30 lb. (per device)Dimension: 4.125 in. W x 1.25 in. H x 4.75 in. DRegulat

IntroductionCongratulations on purchasing MyWirelessTV. is product will allow you to transmit high-denition content from a set top box, gaming conso

Features•Full 1080p HD output - stream judder-free, full high-denition video in 1080p 60Hz with 3D capability•Video Pass-through - main HDTV does not

•HDCP compliant† - secured video content protection with standard HDCP 2.0 encryption•HDMI compliant† - complies with HDMI™ industry standard to assur

Getting To Know MyWirelessTVis section contains a quick overview of MyWirelessTV, including all ports and LEDS on both the MyWirelessTV Transmitter a

Sync LED e Sync LED, located on the front of the Transmitter, is used to display the state of synchronization between the Transmitter and Receiver(s

Transmitter Rear PanelPower Port e Power port, located on the back of the Transmitter, is used to connect the Power cord to the Transmitter.HDMI Inp